Blog · Guides
Power out in one room but the trip switch has not gone? Here is why
The lights work in the hallway and the kettle boils in the kitchen, but the sockets in the bedroom are dead. You open the fuse box expecting a switch to be down, and everything looks normal. This is one of the most common electrical problems in UK homes, and it usually has a clear cause.
How your circuits are laid out
Your home is split into several circuits, each protected by its own switch in the consumer unit (fuse box). Typically there is one or more circuits for upstairs sockets, downstairs sockets, upstairs lights, downstairs lights, and separate circuits for things like the cooker or an electric shower.
A single room is rarely on a circuit of its own. So when only one room goes dead, the fault is usually somewhere along the circuit that feeds it, not in the whole circuit.
First, check the obvious
- Is it lights or sockets? Lights and sockets are on different circuits. If both are dead in one room, it points to two separate faults or something affecting the whole area.
- Look closely at the consumer unit. A tripped switch can sit only halfway down and look as if it is on. Switch each one fully off and back on again.
- Check for a fused spur. Some sockets and appliances are fed through a switched spur with its own fuse, often near the kitchen worktop, a boiler or a heater. A blown fuse there can kill power further along.
- Old fuse box? If you still have rewirable or cartridge fuses, a blown fuse will not look any different from the outside.
Why the power is out in one room when nothing has tripped
When nothing has tripped, the most likely cause is a broken or loose connection somewhere on the circuit. Electricity reaches each socket in turn, so a connection that has failed at one socket can cut the power to every socket after it, often in just one or two rooms.
Common reasons a connection fails:
- a loose terminal in a socket, switch or junction box, which works loose over years of use
- a socket that has been changed or moved and not reconnected properly
- a cable damaged by a nail, screw or floorboard during DIY or building work
- overheating at a connection that has finally burnt through
- rodents chewing cables in a loft or under floors
Loose and burnt connections are the part to take seriously. A connection that is failing can get hot before it gives up completely.
Warning signs to look for
Have a look, without opening anything, at the sockets and switches in and around the affected room. Call an electrician and stop using that circuit if you notice:
- scorch or brown marks on a socket, switch or plug
- a socket or switch that feels warm
- a burning or fishy smell
- crackling or buzzing
- a socket that is loose in the wall
If you smell burning or see smoke or sparks, switch off at the mains if it is safe to do so, and keep away from the affected area.
Simple checks you can safely make
- Unplug everything in the affected room.
- Switch each circuit breaker and RCD fully off and on in the consumer unit.
- Check any fused spurs nearby are switched on.
- Test with a lamp you know works, rather than an appliance that might itself be faulty.
- Note which sockets and lights are dead and which still work, room by room. This helps an electrician find the break much faster.
Do not take sockets off the wall or open the consumer unit. Finding a broken connection safely needs the circuit tested with the right instruments.
What if a switch has tripped?
If a breaker or RCD is down and the power is out in one room, the circuit has detected a fault and switched itself off. Unplug everything in that room and reset it once. If it trips again straight away, leave it off and call an electrician. Our guide on why an RCD keeps tripping explains the usual causes.
How an electrician finds the fault
An electrician tests the circuit to work out where the power stops, then checks the sockets, switches and junction boxes around that point. The fix is often remaking a loose connection or replacing a damaged socket. A damaged cable may need a short section replaced.
If testing shows several tired connections or very old wiring, the electrician will explain the options, from repairing the circuit to planning a wider upgrade.
Not yet reviewed by a qualified electrician.